Author: Jay Andrew

A belated Happy Father’s Day to everyone out there who may be reading this.  This weekend was beautiful, rained for a moment early AM on Saturday but the rest of the day was perfect. We tried again to go fishing, and we saw bluegill swimming around in the shallows. The kids were very excited and determined that today was going to be the day. Alas, it was not. We had bites and nibbles, I hooked one, then lost it. That makes five weekends we have been skunked.  Really think I might need to stick to reloading, this fishing business is giving me the run for my money.

Website Updates and New Stuff

Marc’s post, “Power of a Post-it Note” went live this week.  This will be the first of (what we hope to be) many small but simple things that can be done at the bench to make reloading safer, and more enjoyable for everyone. If you haven’t seen it, you can find the article here.

Much of the recent work has been behind the scenes, so most people won’t notice or see anything appreciable change but there are things in the works. We will announce as we launch or as things are ready to go live.

Time At the Bench

I have spent a bunch of quality time with an L.E Wilson trimmer and trimming brass. As anyone who has spent any amount of time trimming brass by hand knows, it sucks. There’s just no two ways about it. There is a lot of reasons why the Worlds Finest Trimmer, the Giraud Trimmer, and the various versions and knock offs have become so popular. The aim is to get through it all as fast and as painless as possible.

One thing I have always found a little bit cumbersome, and by a little bit, I do mean just a smidge, is measuring the cartridge length before and after trimming. I feel like when I needed to measure brass I pulled it off the trimmer, knocked it out of the case holder, then had to give it a little wiggle as I closed the caliper jaws to get everything square and have confidence in the reading.

This got me looking for a “better” way. By better, really just looking for something that was a tad less cumbersome. I played around with a granite comparator stand, some gage blocks and a dial indicator and came up with something that works quite well. For me it is both faster and less awkward to make quick spot checks to make sure I am trimming the case back each time.

The basic set up is pictured above. I use a dial indicator, in this case a SPI indicator 0 to 1/4  travel. Screw on a 1in diameter foot, which can be purchased from McMaster, and gauge blocks which are stacked to equal my target trim length.

 I zero the indicator on the gauge blocks and push them aside. It then becomes very easy to swipe a case under the foot and take a measurement. The reading is a comparative measurement to the gauge blocks and will let me know if I am .002 from the target trim length, if I am one or zero.  You don’t need the gage blocks, you could trim a case to the length that you want, verified by a caliper check, and then zero off that.

I have found it to be a very quick and easy check and faster than checking with calipers.

Industry and Legislative News

Hearing Protection Act

40+ Firearm Advocacy groups have all signed on to a letter urging the delisting of Suppressors from the NFA. There looks to be strong Republican support, but there are some moderate republicans that have signaled they are not solid “yes” votes.  Of course, every democrat is solidly against the notion with several prominent democrats outright lying that there is no valid legal use for suppressors.

We should expect to have news within the next week if the HPA will be included in Trump’s “Big, Beautiful Bill”. This is being passed through the Budget and Reconciliation process which only requires a majority support. Currently the Senate is made up of 52 Republicans, 51 is needed for its passage. So we can afford to lose one, with Vice President JD Vance available to break a 50–50 tie

ATF – Changing the Rules Again?

There has been a lot of scuttlebutt about the ATF possibly changing its rules when it comes to the “Pin and Weld” method of permanently attaching a muzzle device. When I first came across this, I am a firm believer in the Bongino rule.

           “Wait 24 to 72 hours before believing any breaking news story.”

What Happened?

What we know is that the Gun Owners of America (GOA) filed a Freedom of Information Request (FOIA) which exposed an internal incident occurring in 2021, where an ATF Firearms Tech branch agent, Eve E. Eisenbice, dismantled a pinned-and-welded muzzle device from an imported Beretta handgun using a vise and breaker bar. After breaking it, the agent deemed the installation “not permanent”.

The question has been raised as to whether this will elicit a policy change from the ATF.

Who Is Eve Eisenbice?

Eve E. Eisenbice is, to put it bluntly, a nut case. One that I hope this administration decides to fire as she has a history of making extreme or absurd legal claims. Among her past assertions

• Pillows and potatoes can function as suppressors (and are thus regulated as such provided that you intend to use them as such)
• Check Rests constitute a stock
• Metal Water bottles could be used to manufacture a firearm and thus could be considered a firearm.
• Threaded titanium tubes could be considered suppressors by virtue of their features

Why This Story Took Off   

This isn’t the first time the ATF has been accused of pushing boundaries. Historically, they’ve leaned on Chevron Deference, a legal precedent that gave administrative agencies wide latitude in interpreting regulations, even beyond their statutory authority.

Chevron Deference was overturned on June 28, 2024, which weakens the ATF’s ability to impose sweeping rule changes without clear legislative backing.

So, does this mean the ATF won’t keep trying? Not likely. But it does mean they’re less likely to succeed when challenged in court.

Is a Policy Change Coming?

No formal policy change has been proposed. One rogue agent with a history of overreach destroyed a barrel (not a firearm under federal law) and claimed that somehow invalidated the entire concept of a permanent muzzle attachment.

If the ATF intended to act on this, they would’ve done so in 2022 when they had more leeway. That they didn’t suggests they viewed Eisenbice’s findings as fringe—and not legally defensible.

What’s Really Going On?

This story has been heavily sensationalized, especially by GOA and several YouTube channels, many of which have used it as a fundraising vehicle. That’s what bothers me more than anything.

The ATF is going to do what the ATF always does. But I expect more from those who represent our industry, namely more honesty, less fear-mongering.

Anderson Mfg Closing its Doors

The last bit of news: Anderson Manufacturing is closing down. disappointing, but not entirely surprising.

While best known for budget AR-15 lowers, Anderson had expanded into full rifle builds and even released a Glock-style pistol in recent years.

The industry is currently in what I’d call “Trump Slump 2.0.” It’s not as dramatic as the first one, but market conditions have tightened. The modern sporting rifle segment, ARs in particular, is especially competitive, with players like Palmetto State Armory dominating on price and marketing.

Companies like Anderson, Del-Ton, and others are either shutting down or scaling back. The powder shortage continues, and the broader economy isn’t helping when it comes to disposable income.

New Guns and Gear

There was not anything new that caught either myself or Marc’s eyes. So we’re going to skip this section this week.

We hope everyone has a good week and we’ll catch you next Monday.

Jay & Marc

The Ballistic Assistant is a website dedicated to the art of handloading and shooting. We aim to share tips on reloading and shooting, inform others on what’s going on in the firearms community, and provide our opinion and thoughts on firearms related news and events. If you like what you read, we only ask that you subscribe and share with a friend or two.

If you have any questions, comments or ideas we would love to hear from you, contact info is provided below.

Jay – jay@theballisticassistant.com

Marc –Marc@theballisticassistant.com

Monday always sneaks up faster than it should. It has been a very wet spring; we are on the fourth weekend straight of rain. No fishing this weekend, just rain.  That’s fine, more time at the loading bench.

Website Updates and New Stuff

This week we are welcoming Marc as a contributor to the site. He and I worked closely together doing product development at a previous employer. He brings with him a wealth of wisdom when it comes to reloading (and life), much of it practical know how that it was done before the age of the internet.

To introduce Marc, we have updated the “About Us Page”

We are working on a landing page for him but expect to see practical tips and tricks in reloading that get lost in the internet noise.  His first article can be found here.

How the Internet Almost Blew Up My Gun

I am working on a few things on the website, trying to get formatting and stuff to look right on Mobile. If you see some things that are off or just plain annoying on a mobile screen, I am working on trying to fix those.

Time at the Bench

As before, I have been working on getting caught up on my reloading. Sorting brass, depriming, cleaning, checking case length, annealing necks. It’s a chore; personally, I find it somewhat satisfying and a good way to unwind in the evening. This week it was about processing some 308 Win and 45 ACP. 

My vibratory tumbler survived another week, though the motor stalled out once. It picked back up again a moment later, no magic smoke so we’ll let it ride.

I have got a few things in the mail, case holders for my L.E Wilson trimmer, and the Lee Ram Prime, for priming some of the tight primer pockets. For $20 bucks I think this little tool is well worth it.  

Industry and Legislative News

Hearing Protection Act

There has been no meaningful movement on the Hearing Protection Act. It remains in the Senate, and right now there is quite a bit of drama going on over this bill. No so much regarding the Hearing Protection Act, but the amounts of taxes, spending, ect. That drama has been all over the news, so I do not think I need to touch on it here. However, I am, like many of you, waiting with bated breath to see if this thing survives.

Supreme Court Rulings

The Supreme Court tossed the lawsuit that had been brought by Mexico against 14 different gun companies. Essentially accusing them of making their arms easy to traffic and blaming them for the violence South of the Border. This whole case was a shame to begin with, something dreamed up by Gun Control Groups and politicians. The court ruled that the “Protection of Lawful Commerce in Arms Act” shielded the gun companies from this frivolous lawsuit.

Last week we were disappointed in the courts, this week we are applauding them. That seems to be the nature of things. Alan, one of our subscribers put a plug in for a good resource on the Supreme Court and other legal news. 4 Boxes Diner on YouTube, the host Mark Smith, is a constitutional attorney and really does a good job breaking things down.

Abolish the ATF?

There has been a bit of buzz about the possibility of the ATF being rolled up in the DEA while no formal plan has been submitted, the rumors seem to be an attempt to float the idea prior to a specific policy proposal. What a nightmare that will be. The DEA is probably the worst three letter agency when it comes to constitutional rights. They believe heavily in civil forfeiture and regularly abuse this power.

The last thing we need is the DEA to expand its jurisdiction to firearms. This would be my one critique of the “Abolish the ATF” movement. We can all agree that the ATF is an unconstitutional infringement on the 2A. However, we sometimes overlook that the government rarely gives up power, there will be something that fills the vacuum, and whatever that is may be, far worse than what we were dealing with.

Remember….

“Democracy is the theory that the common people know what they want and deserve to get it good and hard.”
— H. L. Mencken, A Little Book in C Major, 1916

In this light, maybe we are better off remembering the wisdom in old Irish proverb “Better the devil you know than the devil you don’t.”

New Guns and Gear

Barrett Firearms

Personally, I have always really liked Barrett Firearms Manufacturing, the firearms company. They are a modern story of one man, Ronnie Barrett, with an idea that he took that and built a company around it. The cool part is that idea resulting in the Barrett M82/M107. They have been working on what can only be described as a love child between the M107 and the M203.  

Figure 1:Barrett & MARS Inc. 30 mm Precision Grenadier System (PGS)

I vote this as the firearm most definitely going to be included in the next Call of Duty, if it hasn’t been already. It launches 30mm grenades which are programmable for air burst. Of course, designed to engage units which are behind cover, it also doubles as anti-drone as the rounds are programmable.  This was a joint project between Barrett and Montana based MARS, Inc. The official news is that this beat out the FN submission in the xTech Soldier Lethality competition, which does not guarantee adoption, but it does look like it is headed in that direction.

This is not Barrett’s first time in the “larger than .50 Cal” In the early 2000’s I remember reading about the 25x59mm XM109 which was designed to be an large bore upper for the 107. It was a programmable grenade launcher. However, it never made its way past the prototype stage.  No doubt much of the lessons learn in that were used in this most recent venture. Sometimes that’s how the development cycle goes.

Trigger Tech

Trigger Tech is releasing their new Glock Trigger this week (June 10^th 2025). Called the ACE Trigger system, it is a little bit different than your typical drop in Glock Trigger.  Trigger Tech has completely redesigned the trigger system to deliver a 1911 like trigger in a Glock.

It looks like it may retail for about $280 at your favorite dealer. Personally, I am a big fan of trigger tech, every time I have tried their triggers, they seem to be top notch. Sometimes it’s not about buying a new gun but making an existing gun better. An aftermarket trigger is a really good way to make your favorite gun feel like a whole different animal.

Personally, I am not a big fan of Glocks, so this trigger won’t help me much. Here’s hoping that expand this line for H&K VP Pistols. I’d really love to see a trigger for a VZ-58 (I am dreaming now).  Regardless I have a couple of their triggers in a few AR’s, and I am very happy with them.

That’s what we have for this week.

We’d love to hear your thoughts or answer any questions you have,

Jay & Marc

jay@theballisticassistant

marc@theballisticassistant.

Today is Memorial Day. Let’s take a moment to remember those who gave all so that we may remain free people. It is a shame that this holiday has become so commercialized, and that people are more apt to look for the “Memorial Day Sales” than to take a moment to pause and think of those men and women who gave everything. 

Website Updates and News

In terms of website updates, we have one! The new burn rate chart is finally live [LINK].. We included a few new powders that have been released over the past three years. Mainly Hodgdon powders.

Time at the Bench

The last few weeks I have been working on getting caught up on my reloading. I had a large pail of collected brass, some that I shot myself, some that I picked during range trips.  I have been cleaning that, then running it through a decapping die and cleaning it some more. I really don’t like putting dirty brass on my presses.

 I have loaded quite a bit of 45 ACP and have switched my Dillon 550 over to load 9mm. I think this is the first time I’ve loaded anything else besides 45 ACP on that press. Switching over a Dillon 550 is not hard, it is straightforward it just takes a little bit of time to get everything swapped over and the dies adjusted right.

As far as rifle loading, right now I have been working through the backlog of 30-06 brass I have collected. Mainly I am loading for my FN Mauser in 30-06. I’d like to spend more time shooting that rifle and getting it dialed in. For the load I am running 44.0 grains of N140 under a 168-grain Sierra MatchKing.

I hear Marc is working on some loads for his 45-70. Last time I helped him work up a load he did me a favor and let me test the loads in his Marlin Lever gun. I’ve shot 45-70 before, I had not shot “that” 45-70, and I decided I didn’t much care to shoot it again.

Industry News

Progress of the Hearing Protection Act

The obvious buzz in the industry is the excitement over the possibility of suppressors being removed from the NFA.  The Hearing Protection Act (H.R. 152 / S. 494) cleared the House on May 24, 2025, and is now in the Senate. Now is the time everyone should be on their phones calling their respective Senators to keep this legislation in the bill passed by the House.  I tend to be pessimistic about stuff like this, while a new important milestone that has been reached there is much politicking to be done.  Still, I have a few guns I would love to “accessorize” with a can.

Adjacent to this is the blowback the Silencer Central is getting. I personally have been slow to get upset over this. Brandon Maddox, the CEO Silencer Central and Banish suppressors, gave an interview to Tom Gresham of Gun Talk which aired, Sunday the 18^th.  The CEO laid it all out, and I found his explanation about the accusations credible. There is no doubt that if suppressors are removed from the NFA just about any company that makes suppressors is going to see a demand so great that we may see a new industry bubble.

It has been my observation that the Gun Owners of America (GOA) has a tendency to want to make a lot of noise and then fundraise over it. They are not beyond taking on other gun right’s groups if those groups do not take the same 100% No Compromise approach that GOA champions. After reviewing a lot of online commentary, and listening to the interview on Gun Talk, I truly believe this is a manufactured narrative pushed by GOA for the purposes of stirring the pot and then fundraising off emotions. Boy, do we love a good conspiracy theory, and we can often be very quick to eat our own before the full story can be released. Moving on.

ATF settles with Rare Breed over Forced Reset Triggers

Rare Breed, the company behind the Force Reset Trigger, reached a settlement with the ATF in May 2025. While details are limited, it appears the ATF has dropped its classification of the FRT as a machine gun, though stipulations remain regarding use in handguns. This is a stunning about face that I don’t think anyone saw coming.

For those who are not familiar with Force Reset triggers, it still complies with the definition of “Semi-Automatic” as it fires one round per actuation of the trigger. The hammer and sear are mechanically returned to a non-firing state prior to being tripped by the shooter and fundamentally work different from auto sears. As a shooter you are able to increase the rate of fire and prevents you from getting a “Dead Trigger” because you have overrun the bolt.  The ATF had sought to classify these as a machinegun conversion.

With the this new Trump Administration we have the largest swings in governmental attitude towards the 2^nd amendment in my lifetime, and quite possibly since the turn of the 20^th century.

As always, my concern here is when this political pendulum swings the other way, how many of these changes are going to withstand the test of time in five years or ten years? Then what will be the state response? As we have seen, many states will pass laws for what I chalk up purely to spite.

Legislation Efforts to Ban Glock Pistols

To reinforce the point there are  many efforts in states across the nation in restricting or banning firearms. This is probably the most notable in California where they are seeking to ban any firearm that can be readily converted into a machine gun.

This is mostly targeting Glock pistols as there has been a surge in the availability of so- called Glock Switches (Pictured Right) . Regardless of if you are a Glock fan or not (personally they are not my favorite) it is admirable that the basic design has not changed much since the initial release of the Glock 17. The means that for most of the Glock models’ parts are interchangeable.  Several states have filed lawsuits, claiming that Glock refuses to “fix” their pistols, so that “Glock” switches become irrelevant.

As per usual, these laws seek to make something that is already illegal (it is illegal to modify a firearm to fire more than one round per press of the trigger) to be more illegal. Because making things more illegal, always seems to solve the problem *Sarcasm*.  With California, you can count on them to try this, it will be challenged legally, and it will go to the 9^th Circuit Court, which then will likely rule in favor of California, and it will be a crapshoot if that makes its way to the Supreme Court. Other States would have to do a similar thing and we would like need a circuit court to rule the opposite of the 9^th circuit.  A process that takes half a decade or more.

Never mind that the Glock Pistol is the definition of “Common Use” as outlined in the Heller decision.

New Stuff

For those who use QuickLOAD. The 4/29/2025 QuickLOAD update is available now. You can find that here.  This updated amends the Cutting-Edge Bullet Database, however like all QuickLOAD updates it will update all the databases with the most current information. If you load a lot of Cutting-Edge Bullets, or you are a few updates behind it is probably worth looking at this update.

Weatherby has launched a new line of rifles: the Model 307, which is compatible with Remington 700 accessories. This is something I can really get behind, anytime you have a manufacturer back a design, whether it is an MSR or bolt gun, I think it is a good thing. It creates more demand for after-market accessories and this benefits everyone.  It is also nice to see Weatherby offering just the action for those guys who like to build rifles.

Springfield Armory has launched a new chassis version of their 2020 bolt action and have called it the Heat Seaker. Marc’s first impression of this was “Who came up with that name?”.  Chassis bolt guns have become popular, especially with the PRS crowd. It’s the flavor of the week right now, no doubt it’s a quality rig. For the price point it better be.

Lastly I wanted to say thank you to all those who wrote in to welcome me back. It was not something I was expecting, and I was grateful to receive so many messages of support.

That’s what I have this week.

Jay

It has been a long time since I have updated the website. At the beginning this absence was due to some family issues. That has since been resolved, favorably. After that it was about getting settled into a new home and a new job. After a 3 year hiatus, I have finally found some time to start back again.

During this time I worked primarily as the New Product Developer for Creedmoor Sports. Odds are you may have seen videos of me on YouTube going over new products. I can honestly say doing product development in the reloading space has become a passion of mine. I worked closely with and developed a deep friendship with Marcus Brown. Together we brought nearly two dozen new products to market with many other getting design updates and improvements. 

That began to change in the fall of 2023, there was a noticeable slowdown in the market. The shooting sports, and particularly our little niche area is highly dependent on disposable income. I strongly suspect that as COVID money dried up and as Americans began to feel the pinch of inflation all the disposable dollars people spent on their hobbies began to dry up.  COVID created a bubble of demand, and I suspect many companies gobbled that demand up, not realizing it was a bubble, and made plans to grow and expand. When the bubble began to subside, the companies that made purchases and tried to expand were left with crippling debt.

Marc and I had more ideas and more designs than we could bring to the market. It was an unfortunate reality of the business, the development cycle is expensive, and it can be hard to go from concept to design unless you have capital to back it. When sales fell so did the appetite for risk, and despite our successes with items like the Wind Indicator, the line of Enhanced Turret Heads, The Comparator Tool, and various other reloading items, the company became risk averse and scaled back.

I have been part of sinking companies before and could see the writing on the wall. I started looking for another job early in 2024, leaving Creedmoor Sports at the end of May 2024. We moved north to the New England area not far from where I grew up.  Marc was at Creedmoor for about another year, and we stayed in touch. He was unceremoniously dismissed from the company at the end of February 2025, due to slow sales. As a southern boy through and through he remains in the south.

Despite some bitter moments, I largely see the three-year period as an amazing period of growth for me. I learned a tremendous amount from the industry, about the product development cycle, and about the market. I also made several connections and lasting friendships that have extended well beyond my employment. It also gave me an opportunity to be exposed to a lot of different reloading tool brands, and I began to develop more of a sense of what I liked and what I didn’t. Brands like L.E. Wilson, and Triebel began to help me see what quality reloading tools could and should be.

I’ve also added new cartridges to my handloading menagerie. Most notably .458 SOCOM and .357 Sig. This has come with a few new guns and gun builds which I am sure I’ll discuss at some point.  It was not a direct intention of mine to get into short and squat cartridges but I have a collection now. 300 Blackout, 357 Sig, 458 SOCOM, and 338 Spectre it’s becoming a trend.

What is the future for the Ballistic Assistant?

The move north has brought stability and an opportunity to finally set up my reloading presses and spend evening slowly working through the backlog of handloading tasks that have piled up over the years. As handloading does, you have lots of time to think, and both Marc and I have a long list of things we would like to bring to market. That will be our next step. I’ll continue to build out this site, offer commentary on current firearms news. Discuss and share projects I am working on, and overall try and keep building this website as a resource for the handloader.

In the meantime, I have been working on an updated burn rate chart. There have been some new powder releases in the past three years that are absent from the chart. SAAMI has also accepted several new cartridges, including the 5.7x28mm, and the 338 ARC which is Hornady’s interpretation of the .338 Spectre.

Federal has introduced the 7mm Backcountry, which has elicited an eyeroll from me on the marketing. I remain unconvinced that steel case ammo and 80kpsi cartridges are the wave of the future. I am also skeptical of Federal’s claims that it can be reloaded, the rumors are that die manufacturers are having a hard time creating functional sizing dies.

We are likely to see big changes on the ATF’s positions on several firearm accessories. We have already seen an about face on the Forced Reset trigger, I suspect there will again be reclassification and changes regarding the rules around pistol braces for the 100^th time. I’m also not convinced that any of these changes will last much longer than the next Democratic Administration. I have seen a lot of enthusiasm for possible removal of suppressors from the NFA. Something I completely support and would love to see. However, the realist in me will “Believe it when I see it”, it is not something I expect will happen in this congress.

The industry has seen an explosion in double stack 1911, often called 2011 though the term is trademarked by Staccato, who used to be STI. Everyone who is anyone is putting out double stack 1911’s. I have to admit, they are a pretty nice update to a 100 year old design. Time will tell how long this trend continues.

I have all but dumped the social media scene. It was a tremendous time suck and while I know it is good for website and business growth it also kills a lot of my time.  So I have unceremoniously abandoned Facebook, Reddit and Instagram. For now, it is those who have subscribed, which thankfully, it has seen growth in my relative absence.

As always, if you want to get in contact the best way is send me an email at jay@theballisticassistant.com

Till next week,

Jay

Good Monday Evening! I have been fairly busy working on a few things, but felt I needed to try and get an update out there since SAAMI accepted a few new cartridges. This happens every 6 months as that is the frequency that the SAAMI committee meets. This most recent meeting happened at the 2022 SHOT Show.

These are all rifle cartridges and I will be updating the Rifle Cartridge’s Catalog to include these new chambers.

6mm GT

This cartridge was introduced by Hornady. Think of it as a between cartridge. Not quite as big as the 6mm Creedmoor, 243 Win, and not quite as small as the 6mm BR or the 6XC. As with most cartridges, this has been a wildcat for some time and has gained some popularity with those shooting PRS.

The goal of this cartridge is to try and mimic the low standard deviation that is offered by 6BR but still gets gain on some of the velocity you can achieve with the 6mm Creedmoor. As many have found out, 6mm is kind of a sweet spot as it combines low recoil with high BC.

6.8 True Velocity Composite (6.8TVC)

This is probably the most interesting cartridge in the SAAMI catalog. It is the first cartridge that is based entirely on polymer case technology. You will note there is no external case neck. The case stops at the shoulder.

The big advantage of polymer cases is weight. Brass is dense and replacing it with steel or aluminum nearly always results in a dramatically lighter case. However, nothing is quite as dramatic as replacing it with a polymer case. This is not a new technology, after all, we have been using polymer for shotgun shells for some time. To see it used with rifle and at service pressures of 65kpsi, is a relatively new thing.

The 6.8TVC is aimed at LEO and Military contracts as a polymer case that can increase the number of rounds a soldier can carry. There has long been a push to increase the caliber from 5.56 to something larger, and the 6.8 caliber has been bounced around a few times.

I have previously been critical of the polymer cases as I have been concerned about what happens when a polymer case gets left in the chamber. As it was pointed out to me that polymer does not conduct as much heat into the chamber, and the chambers do not get as hot as fast. I have also been reassured it is not an issue. With several militaries evaluating the technology globally, it will be interesting to see how quickly this gets adopted.

A few other things of note is the cost of polymer is substantially lower than that of brass. For those looking to pinch pennies and still shoot; polymer may be the way to go. TVC also claims that neck tension is far more consistent with their ammunition than what is achievable with brass, resulting in more consistent and accurate ammunition. All things to consider, but still I think I will be slow to make this transition.

338 Weatherby Rebated Precision Magnum (338 WBY RPM)

For those looking for a new magnum cartridge, Weatherby has a new 338 Magnum. The rebated rim allows it to be used on a rifle with a .473in bolt face. For comparison that is basically any 30-06 or 308 Win family cartridge. This cartridge is more or less a necking up of the 6.5 Weatherby Rebated Precision Magnum.

I suppose the purpose of these cartridges is to have a “Magnum” chambering in your caliber of choice while also having an ultra-light rifle. I do not see anything in these cartridges that would make them better choices for long-range targets or hunting when compared with what we already have.

If you are someone who hunts a lot and would like to save some weight on your pack gun, I suppose this might be something to look into. However, I am not sure the performance or the potential weight savings is going to justify the cost of a new rifle. That’s just me, someone else who is a bit more “High Speed, Low Drag” may disagree.

That is the new SAAMI cartridges for this meeting. I suspect next meeting we will see the 30 Super Carry on the list given Federal and Smith & Wesson are in current production. The jury is still out on that new cartridge. I have a few of your looking for versions of the Powder Burn Rate Chart. I am in the process of updating it and will send it out when completed. It takes time to hear back from companies on their powders and then takes a bit of time to do some research to place the powders in relative order. It will be a little bit longer before I publish the updated version. Thanks for being patient.

As always if you are looking to get in touch, the best way is to send me an email at jay@theballisticassistant.com. You may check us out on Parler, Facebook, Instagram, and Reddit. If you’d like to submit a load to our load database, the instructions are here.

As always, shoot straight and stay safe!

The Ballistic Assistant

It’s a day late, and I’m a few dollars short. As per the usual. I’m late in posting this because I wanted to get the SHOT Show 2022 Summery finished up. It is now live on the site and can be read here. It’s a longer read then usual but hopefully it has a few product highlights that have not made it on the typical gun rags.

For those who want the condense version here are a few thoughts on it. There has been a lot of rumors about attendance. It was sparse, but that was not a bad thing. Remember SHOT show is an opportunity for vendors, manufacturers, suppliers, and other supporting parties to meet up and discuss business. Yes it is a big to-do and everyone is displaying the cool and new product, but it is less about that and more about trying to make those connections.

So having fewer people there meant we actually able to get more done. Fewer people were kicking the tires and poking around, and more people were actually there to talk business. This made it a very productive trip for the folks who did go. Even though there were a few major vendors and gun companies that decided not to go, there was plenty to do and see. The biggest benefit of all of this was that you could walk at your own pace rather then the pace of the mob that typically clogs the aisles.

This made it feasible to actually see the whole show in a few days. I put in a little over 50,0000 steps covering about 25 miles in three days. However I saw a lot, and I got to talk to a lot of vendors. From that aspect, it was actually a really good show.

To read the full write-up with my product highlights click on this link.

I’ll be posting a lot fo the pictures I took over the Ballistic Assistants Instagram Page. So be sure to check it out.

As always if you are looking to get in touch, the best way is to send me an email at jay@theballisticassistant.com. You may check us out on Parler, Facebook, Instagram, and Reddit. If you’d like to submit a load to our load database, the instructions are here.

As always, shoot straight and stay safe!

The Ballistic Assistant

It has been a busy beginning of the year, so this is the first update I’ve been able to scratch out for the new year and it will be a short one. We did do a new write-up on Creedmoor’s Enhanced Press Head for the Redding T-7 Press. As with a lot of these product highlights it’s telling the story of how we came up with it and why we did what we did.

You can find the write up here, and if you are so inclined to try out one of these heads, let me know what you think of it. Shoot me an email or leave me a comment.

I will be headed out to SHOT Show this year. It is likely going to be somewhat of a muted show. Several high profile companies will not be attending, and I suspect over all attendance will be down quite a bit due to COVID. It is unfortunate but there are some new things being launched. With demand being so high for pretty much everything firearms-related, it will be hard to say how much new stuff will be showcased and of that stuff what the timeline of availability will be. However I am sure I’ll be doing a highlight article to show what thing I found to be interesting.

Like I said this would be short and sweet. There are a few things I am working on in the background for the website, rumor has it I am going to be offloading some of my brass collection. We will see. As always if you are looking to get in touch, the best way is to send me an email at jay@theballisticassistant.com. You may check us out on Parler, Facebook, Instagram, and Reddit. If you’d like to submit a load to our load database, the instructions are here.

As always, shoot straight and stay safe!

The Ballistic Assistant

Good Monday Evening! It is that time of the month again, we get to talk about all the great things that have happened over the last week. In website news, the biggest announcement is that we’ve officially crossed 100,000 views. It’s a small number, compared to a lot of website traffic out there but it is a milestone that I am happy to have hit. It took us a little over two years to get there, and I have not spent any money in terms of promoting the site. So it’s a neat achievement. Thanks to everyone who has made it possible.

This past week I have been working on quite a few reloading-related projects, namely processing a bunch of 338 Lapua brass. It’s all once fired brass that has been sitting in storage and needed to be deprimed, and cleaned. If you have not tried it, or have been thinking about trying it, wet tumbling with stainless steel media is really the way to go. The results have always had me impressed, and it typically goes quicker and leaves less of a residue than any other media I’ve tried.

I know that a lot of people are not big on the “Wow” shiny factor on their reloads, and for a long time, I did not care as much either. So long as they worked and did not foul up my die or rifle I was happy. As I am slowing down, getting older, I find I appreciate the little things and sometimes those little things are nice clean shiny brass. While you can definitely get that with a bit of liquid car wax and corn cob media, the wet tumbling method just seems to do it faster.

My only complaint is that getting the primer pockets perfectly clean seems to be tricky. I am using the Stainless Steel pins, and I do wonder if the chips might be a bit more aggressive. I also wonder if the primer pockets might be a bit hard to clean when a magnum primer is used, given the heat and heat-related etching that likely takes place. I am not saying you can’t get picture-perfect, cleaned primer pockets using the stainless steel media and wet tumbling, I just have not found the right combination of time, additives, and pins to get it right for these 338 Lapua cases.

Another thing that may be worth mentioning is that wet media tumbling with stainless steel media seems to be a bit louder than vibratory tumbling with dry media. Which for most people, that’s not a big deal. When you live in an apartment, or you have neighbors directly adjacent to you, it could be a bigger issue. There are some rubber-lined tumblers on the market that are a good deal quieter than the tumbler I have been using. So your experience may vary and you may not have a problem with it. Since the vast majority of hobby-level reloading has been done in an apartment, or other shared space, I am probably unusually wary of the noise or inconvenience that my hobby may have on others.

Cleaning up some brass was not my only firearm-related venture this past week. I also replaced a magazine tube on a Benelli M4. We swapped out the factory reduced capacity importation rule compliant tube, with the US-made “proper capacity” tube. I’ll be honest, I was a bit disappointed, from everything I had read online, and the youtube videos that I have watched, I expected it to be a hassle. In an odd twist of fate, it was not. It was a pretty straightforward process. I’ll have a write-up done on it in a few weeks. Suffice it to say, this was not a big issue, and I may be I got lucky, but I wonder if people are not warming up the receiver enough to break down the thread locker that Benelli applies at the factory.

That is everything I have for this week. There are a few things I am working on in the background for the website, things take a while to come together, so stay tuned for that. It likely will not happen until after the holidays. As always if you are looking to get in touch, the best way is to send me an email at jay@theballisticassistant.com. You may check us out on Parler, Facebook, Instagram, and Reddit. If you’d like to submit a load to our load database, the instructions are here.

As always, shoot straight and stay safe!

The Ballistic Assistant

Good Evening all. It’s has been a busy last week. I have spent some time working on a few reloading projects and prepping things for the website. Once everything is ready I’ll make a formal announcement but there are a few changes that are coming that I am hoping will bring some good things to the website and help it grow.

One of the most popular projects I did on the website was the VZ-58 build. It is constantly in the top ten pages. I wanted to expand on some of that, there will be more to come to help finish that project out to a good conclusion but for right now I wanted to build a resource for people looking to build their own VZ’s. Here is the link to a new page I’ve started and will maintain for those looking to complete or start their build: VZ-58: Parts and Supplies

If you are a company looking to get listed, please let me know and I’ll add you to the resource page. I do not charge or ask for anything in return, it is just a tool to save people time.

Last week I wrote up and published a new product highlight. This is for Creedmoor Sport’s TRX-925 precision reloading scale. I wanted to tell the story of the development of the scale and why we did what we did. We have been surprised by the amount of conversation it has started. Hopefully, I can help clear up some of the questions, and some of the concerns about the scale. Here is the link: Product Spotlight TRX-925 Scale

This update will be short this week as I’ve got some actual reloading-related activities to do. As always if you are looking to get in touch, the best way is to send me an email at jay@theballisticassistant.com. You may check us out on Parler, Facebook, Instagram, and Reddit. If you’d like to submit a load to our load database, the instructions are here.

As always, shoot straight and stay safe!

The Ballistic Assistant